Here are a few reasons why:. Travertine tile is an incredibly popular choice in homes and commercial buildings throughout the world. However, a few cons can hold some people back, including cost and feel. Is travertine tile the right option for your next project?
Your email address will not be published. Learning Center Find the answers to your home improvement questions. Shop All Travertine Tile. Related posts: Natural Stone Tile vs. Leave a Reply Click here to cancel reply. December 13, at Hi Allen — thanks for reaching out to us!
We would probably recommend using a product like composite deck boards over travertine, as they have more flex to them. With that being said, it is possible to use travertine for this type of application, but you have to make sure that you have a solid substrate that is flat and can handle any erosions, so we would recommend removing the old boards. Any movement in the substrate can cause the tile to crack or break.
Even though travertine is commonly used around pool decks, it is important to note that this material can be slippery when wet. September 12, at I really hate dirty and discolored grout which is why I am thinking of installing travertine. For some reason I believe I can install it indoors without grout, similar to pavers.
Or am I misinformed about installing travertine like pavers?? If I must use grout, I understand that a rectified edge gives you a small grout line — does chiseled give you a zero grout line? September 13, at Thank you for getting in touch! You will need grout for all travertine tile, no matter if it is rectified or has chiseled edges. Chiseled edges just give you more of a jagged edge to make the grout lines look more natural.
With rectified edges you can use the smallest grout line possible, but you still need grout. To avoid having the grout change color you can seal it, we also have pre-sealed grout available to skip that step after installation. August 10, at We are having travertine installed by our pool. Can it be installed directly into concrete with no underpayment or is it better with a sand base?
August 17, at You will need a sand base beneath the Travertine. There will be too much friction between the concrete and Travertine if you lay it down without the sand. June 28, at I have considering purchasing Travertine tile for our kitchen and entrance way. I have what is the best way for cutting the tile?
Does this tile break clean with a good scoring? I have a dry tile blade for my circler saw would I be better off renting a wet saw? June 29, at You will need to use a diamond blade on a wet saw to cut the travertine. You will not be able to just score and break the tile.
June 2, at Hi John. Thanks so much for reaching out to us! Yes, concrete really is the best option to use. A big part of proper installation is having a subfloor that is smooth, level, dry, clean and has no movement to it. Any movement in the subfloor will transfer to the tile and cause it to crack.
Please let us know if you have any other questions. February 22, at What is the best adhesive to use on floor install of travertine. Insofar as adhesive I have read recommendations to use a white adhesive. Once you have your previous covering removed and all of your materials on hand, you should prepare the surface for tile. Make sure to use a damp rag to remove any dust from the wall after sanding.
For a wood rather than concrete subfloor, lay down 0. Part 2. Mark the midpoint of the area to be tiled. For flooring, you want to mark both the X and Y axis along the flooring in order to find the exact center of the room. Lay out the tile design. With the floor prepped and the center marked, you can lay out the design of the tile.
Start with the center gridline s and place additional tiles leaving the appropriate amount of room for the spacers, which will later be grout lines. For floor tiling, you can use the space you left for the grout to chalk in an entire grid for the project if you so choose. Mix your thin-set mortar. You will not be able to mix the thin-set for the entire project at once. Instead mix small batches in a five-gallon bucket.
Whatever you mix must be used within two hours. Apply the thin-set to a small area. Start with the area where you measured your initial chalk lines and spread enough thin-set to place two or three tiles to start. Use the edge of a V-notched trowel at roughly a degree angle to spread the thin-set.
You want to have an evenly, thinly covered space before putting down a tile. They are supposed to be there as they help air escape as the mortar sets. Apply the first tiles. Place the first tile flush with your chalk centerline s. For a backsplash, the process is easiest to do in rows.
Place spacers. Check for level placement. If you want to take extra precautions to maintain the level surface, you can also purchase a leveling system, which consists of threaded pegs that go between the spacers and knobs that you can gently tighten down against the tops of the tiles to help perfectly level them and hold them in place. Wipe excess thin-set as you go. You can use a damp sponge to wipe it away. Cut tiles around baseboards. As you work toward the edges of your surface, you will likely have to cut some of the tiles to fit them.
Take the exact measurement to which you need to cut the tile accounting for any spacers and transfer the measurement to the tile with a pencil. Then use a wet saw to make the cuts. If you are unfamiliar with how to use a wet saw, then you can find more at Use a Tile Saw. Adding a layer of travertine tiles to your driveway, sidewalk or patio will not only make your home look better but will also increase the value of your home.
Installation would be a perfect weekend project for you and your family. The first step when preparing the concrete for tile installation is to clean the concrete. This prevents dirt and rocks from getting underneath your tiles. This will not only prevent an uneven surface but could also prevent the tiles from cracking under pressure. It is ideal to sweep the concrete of any debris and then go over it with a pressure washer.
It would also be a good idea to mix some soap and water with your pressure wash mix. Once the concrete has been cleaned your next step is to lay down the layer of mortar.
0コメント